Set of 8 pieces valve tappet. Smaller head diameter - 20.3mm - for GT camshaft
Parts
New timing chain camshaft sprocket, 34 teeth with timing mark.
Standard profile camshaft - new made item (not a reground old unit) for chain driven engines. Please note that this camshaft has been hardened to Rockwell C 53 level, when fitted and running...
New made sports camshaft, not an old unit which has been reground). Please note that this camshaft has been hardened to Rockwell C 53 level, when fitted and running engine, a running in oil must...
Three part camshaft bearing set. Standard size only. Used on reconditioned earlier engines also.
Re-manufactured adjustable valve tappet - complete with set screw and lock nut.
Standard size exhaust valve suitable for unleaded fuel, 107.20mm long, head diameter 26.80mm,
oversize 1/16" (approx 1.5mm) than standard valve.
100E engine inlet and exhaust vave guide. 55mm long x 12.7mm o/d x 8mm i/d.
100E standard strength valve spring, Set of 8 pieces.
Dimensions 50mm tall x 22mm diameter, 3.3mm diameter wire.
Dimensions 50mm tall x 22mm diameter, 3.3mm diameter wire.
New, re-manufactured timing chain camshaft sprocket, 34 teeth with timing mark.
camshaft lock washer, dimensions 58mm x 38mm with 35mm hole centres.
three part camshaft bearing set. standard bore inner, standard size outer. this part is used through later model engines also.
three part camshaft bearing set. standard bore inner, standard size outer. this part is used through later model engines also.
standard outer - under size inner 0.002" or 0.010" limited...
standard outer - under size inner 0.002" or 0.010" limited...
three part camshaft bearing set. standard bore inner, standard size outer. this part is used through later model engines also.
single width timing chain with link -application also Escort 1100 or 1300, Cortina Mk1 1300 or 1600, Capri 1300 or 1600, Consul Classic Capri, Corsair 1500, Cortina Mk2 1300, 1500 or 1600ohv,...
105E type exhaust valve. 97.50mm long, head diameter 30.15mm, offered with standard stem (nominal 5/16"), and oversize stem of 0.003" (approx 0.076mm) and 0.015" (approx 0.38mm) diameter...
105E type exhaust valve. 97.50mm long, head diameter 30.15mm, offered with standard stem (nominal 5/16"), and oversize stem of 0.003" (approx 0.076mm) and 0.015" (approx 0.38mm) diameter...
105E type exhaust valve. 97.50mm long, head diameter 30.15mm, offered with standard stem (nominal 5/16"), and oversize stem of 0.003" (approx 0.076mm) and 0.015" (approx 0.38mm) diameter
105E type inlet valve. 97.50mm long, head diameter 32.00mm, offered with standard stem (nominal 5/16") ,and oversize stem of 0.003" (approx 0.076mm) and 0.015" (approx 0.38mm) diameter
measures...
measures...
105E type inlet valve. 97.50mm long, head diameter 32.00mm, offered with standard stem (nominal 5/16") ,and oversize stem of 0.003" (approx 0.076mm) and 0.015" (approx 0.38mm) diameter
measures...
measures...
105E type inlet valve. 97.50mm long, head diameter 32.00mm, offered with standard stem (nominal 5/16") ,and oversize stem of 0.003" (approx 0.076mm) and 0.015" (approx 0.38mm) diameter
measures...
measures...
105E type inlet valve. 97.50mm long, head diameter 32.00mm, offered with standard stem (nominal 5/16") ,and oversize stem of 0.003" (approx 0.076mm) and 0.015" (approx 0.38mm) diameter
Extra strong valve spring set (8 pieces) - approx dimensions 38.5mm tall, 28.5mm diameter, 4mm wire.
Pre-crossflow and crossflow cam shaft with wider lobe machined from billet steel. Later camshaft with the offset locating dowel, supplied with 105E-6256-B later sprocket - with two bolts part...
Camshaft to camshaft sprocket dowel, dimensions 15mm overall length (4mm long major diameter, 11mm minor diameter), 6.4mm minor diameter and 8mm diameter shoulder.
Fits 109E-6250 camshaft for pre...
Fits 109E-6250 camshaft for pre...
Valve spring set, 8 pieces. approx dimensions 37.5mm long, 28mm diameter, 3.7mm wire diameter, Fits:- Consul Corsair Consul Classis Consul Capri
Flywheel and camshaft sprocket bolt, 4 required for flywheel, 3 required for camshaft sprocket, 5/16 UNF X 3/4" long.
sports valve spring, per engine set (8). specify 8/10hp or 100E engine. 100E are made to Terry V.S. 483 spec.
sports valve spring, per engine set (8). specify 8/10hp or 100E engine. 100E are made to Terry V.S. 483 spec.
sports valve spring, per engine set (8). specify 8/10hp or 100E engine. 100E are made to Terry V.S. 483 spec.
13/16" wide. We do have a few of these drives marked 0.004" oversize on outside.
Inlet valve 4 7/32" (107.45mm) long, head diameter 27.8mm, normally used on engines built 1932 to 1939 period.
Standard exhaust quality valve 4 7/32" (107.45mm) long, head diameter 28.15mm, normally used on engines built 1932 to 1939 period.
timing chain tensioner assy, cast aluminium body with spring loaded knurled snail cam. timing chain tensioner assy, cast aluminium body with spring loaded knurled snail cam.
camshaft thrust plug, stepped plunger located at the front of the camshaft, fits into timing cover.
Camshaft to camshaft sprocket dowel, dimensions 13.9mm long, 7.2mm diameter with a 8mm shoulder. Fits :- 8/10hp, 100E, Consul, Zephyr
New, re-manufactured timing chain camshaft sprocket, 40 teeth with timing mark - Please note there are two marks on the outer ring - the ARROW is the correct mark, not the dimple.
Inlet valve 4 9/64" (105.15mm) long, head diameter 28.15mm, normally used on engines built in 1940
Standard exhaust quality valve 4 9/64" (105.15mm) long, head diameter 28.15mm, normally used on engines built during 1940
Exhaust quality, inlet or exhaust valve 4 11/32" (110.33mm) long, head diameter 28.15mm. See also E93A-6505-UN
Oversize head inlet valve, 31mm head diameter, 4.3/8" (111.13mm) long, for tuning purposes.
Premium exhaust/inlet valve for modern fuels 4 11/32" (110.33mm) long, head diameter 28.15mm. Note - requires hard seat in the block.
Later type split valve guide with deep shoulder, eight per engine. Used 1939-59.
oil pump and distributor drive shaft for CHAIN DRIVEN camshaft motor only, Will only fit later engines with chain driven camshaft.
oil pump and distributor drive shaft for GEAR DRIVEN camshaft motor only, Will not fit later engines with chain driven camshaft.
For unleaded fuel. Requires machine work to engine block to fit this part. Dimensions 30.3mm o/d x 23.9mm i/d x 6.3mm thick.
Standard profile camshaft - new made item (not a reground old unit) for gear driven engines (model Y, C or Eifel)
Please note that this camshaft has been hardened to Rockwell C 53 level, when...
Please note that this camshaft has been hardened to Rockwell C 53 level, when...
3/4" wide. We do have a few of these drives marked 0.004" oversize on outside.
Per engine set of 8 pieces. Minimum height 35mm maximum height 49mm. Please note that fitting these tappets enables the user to use shorter than original valves in engines if required.
Prices shown include VAT @ 20% where applicable
