Front inner taper roller wheel bearing, for 0.983" dia stub.
Dimensions 52mm o/d x 25mm i/d x 15mm wide.
Dimensions 52mm o/d x 25mm i/d x 15mm wide.
Parts
Front outer taper roller wheel bearing, Fits 8/10hp cars & 100E.
Dimensions - 41.3mm o/d x 16mm i/d x 14.7mm wide.
Dimensions - 41.3mm o/d x 16mm i/d x 14.7mm wide.
Taper roller inner front wheel bearing assy.
Fits :- 100E & 300E with 1.000" dia stub Prefect 107E Anglia 105E & 307E Cortina Mk 1 1963-66.
Dimensions - 50.8mm o/d x 25.4mm i/d x 15.1mm...
Fits :- 100E & 300E with 1.000" dia stub Prefect 107E Anglia 105E & 307E Cortina Mk 1 1963-66.
Dimensions - 50.8mm o/d x 25.4mm i/d x 15.1mm...
Front wheel outer taper roller bearing, 105E-1216-A and 105E-1217-A Fits:- Prefect 107E (eng no 218338 onwards) Anglia 105E Cortina Mk1 up to Nov 1964
Front inner taper roller wheel bearing.
Fits E83W 10cwt. Dimensions 57mm o/d x 28.5mm i/d x 20mm deep.
Fits E83W 10cwt. Dimensions 57mm o/d x 28.5mm i/d x 20mm deep.
Front outer taper roller wheel bearing, fits E83W 10cwt. Dimensions 49mm o/d x 18.9mm i/d x 22mm deep.
Front wheel hub dust cap/grease retainer.
Dimensions - 32mm inside diameter 51.5mm outside diameter.
Dimensions - 32mm inside diameter 51.5mm outside diameter.
Front hub oil seal, stops grease and oil contaminating the brake shoes. used between 1953-59 with 0.983" stub axle.
Dimensions :- 54mm o/d, 30mm i/d x 7.6mm thick.
Dimensions :- 54mm o/d, 30mm i/d x 7.6mm thick.
Front hub oil seal, stops grease and oil contaminating the brake shoes.
Used on 100E between 1959-62 with 1.00" stub axle. also used on all 105E and Mk1 Cortina 09/62 to 10/64 not GT or Lotus....
Used on 100E between 1959-62 with 1.00" stub axle. also used on all 105E and Mk1 Cortina 09/62 to 10/64 not GT or Lotus....
Front hub oil seal, fits E83W 10cwt and Ford V8 pilot.
Dimensions approx 68.30mm o/d x 37mm i/d x 9.5mm thick.
Dimensions approx 68.30mm o/d x 37mm i/d x 9.5mm thick.
Rear wheel bearing race. Caged roller bearing assy.
Dimensions 61.5mm o/d x 39.6mm i/d x 30mm deep.
These are original unused but poorly stored bearings.
They do show very slight signs of...
Dimensions 61.5mm o/d x 39.6mm i/d x 30mm deep.
These are original unused but poorly stored bearings.
They do show very slight signs of...
Rear wheel bearing repair kit (axle set) Over comes the problem of worn bearing surfaces on rear axle casing.
This part replaces the original Y-1225 with new inner and outer race surfaces...
This part replaces the original Y-1225 with new inner and outer race surfaces...
Rear wheel bearing repair kit (axle set) Over comes the problem of worn bearing surfaces on rear axle casing.
This part replaces the original 100E-1225 with new inner and outer race...
This part replaces the original 100E-1225 with new inner and outer race...
Rear hub oil seal for all 8/10hp cars with the original wheel bearing fitted.
Not suitable for the Y-1225-RK Rear axle wheel bearing repair kit.
Dimensions 64mm o/d x 36mm i/d x 13mm thick.
Not suitable for the Y-1225-RK Rear axle wheel bearing repair kit.
Dimensions 64mm o/d x 36mm i/d x 13mm thick.
Rear hub oil seal, stops grease contaminating brake shoes.
Dimensions 63.5mm o/d, 38mm i/d x 8mm thick
Dimensions 63.5mm o/d, 38mm i/d x 8mm thick
Replacement rear hub oil seal for our wheel bearing repair kits 100E-1225-RK and Y-1225-RK,
Overall dimensions 63.7mm outside, 46.5mm inside, 6.3mm thick.
Overall dimensions 63.7mm outside, 46.5mm inside, 6.3mm thick.
100E Spun steel front hub grease cap, 41 mm interference fit into front drum, preventing grit getting into the taper roller bearing.
Dimensions - 40mm diameter taping down to 30mm, with 45mm...
Dimensions - 40mm diameter taping down to 30mm, with 45mm...
front hub outer bearing snap ring. dimensions 43.25mm outside dia, 35mm inside dia, 2mm thick.
aluminium 4 piece wheel trim for 13" wheels. 4 parts supplied as car set.
Plain top, later style hub cap.
Approx. 238mm overall diameter. inside edge approx 226mm.
Approx. 238mm overall diameter. inside edge approx 226mm.
shouldered wheel stud, fits rear drum only, 7/16 unf thread, overall length 38mm.
Castellated front stub axle hub nut 3/4"UNF for E83W 10cwt.
32mm across the flats x 15mm deep.
32mm across the flats x 15mm deep.
Large aluminium front hub grease cap, preventing grit getting into the taper roller bearing, fitted on E83W 10cwt vehicles.
Threaded base and hexagonal top. 50mm in diameter x 32mm tall, 44mm...
Threaded base and hexagonal top. 50mm in diameter x 32mm tall, 44mm...
Rear wheel bearing race. Caged roller bearing assy.
Dimensions 70mm o/d x 52.8mm i/d x 42.2mm deep.
Very limited stocks.
Dimensions 70mm o/d x 52.8mm i/d x 42.2mm deep.
Very limited stocks.
Retaining spring clip fitted to wheel to hold hub cap onto the road wheel (5 per wheel).
Overall height 37mm with a 5mm fixing hole, width at base 13mm tapering down to 8mm.
Overall height 37mm with a 5mm fixing hole, width at base 13mm tapering down to 8mm.
Domed primer painted hub cap with raised centre section.
Approx. 260mm overall diameter. inside edge approx 227mm.
Approx. 260mm overall diameter. inside edge approx 227mm.
original refurbished hub cap, finished in grey primer ready for final colour.
Rear hub oil seal for the Ford E83W 10cwt.
Dimensions - 81mm o/d x 51mm i/d x 11.3mm thick.
Dimensions - 81mm o/d x 51mm i/d x 11.3mm thick.
Rear hub gasket washer.
Black fibre washer fits under rear hub nut retaining washer.
Dimensions 25mm o/d, 16mm i/d, 3mm thick.
Black fibre washer fits under rear hub nut retaining washer.
Dimensions 25mm o/d, 16mm i/d, 3mm thick.
Front wheel bearing retaining washer with inner locating tab.
Dimensions 45mm o/d x 19mm i/d x 3.5mm thick with a 4mm key way tongue.
Dimensions 45mm o/d x 19mm i/d x 3.5mm thick with a 4mm key way tongue.
Wheel nut for the 8/10hp cars and 100E models, 7/16"UNF thread, 3/4" A/F hex flats..
Chrome plated raised centre hub cap.
Approx. 166mm overall diameter. inside edge approx 145mm.
Approx. 166mm overall diameter. inside edge approx 145mm.
Raised dimple top, chrome hub cap . For 100E, 300E & 107E also suit Consul, Zephyr & Zodiac Mk1. weight approx 400gm.
Approx. 238mm overall diameter. inside edge approx 226mm.
Approx. 238mm overall diameter. inside edge approx 226mm.
inner front wheel bearing spacer, fits 0.983" stub axle.
inner front wheel bearing spacer, fits 1.00" stub axle.
Rear hub grease/oil seal snap ring, 81mm outside diameter, 72mm inside diameter, 4.5mm thick.
Domed chrome plated hub cap with raised centre section.
Approx. 260mm overall diameter. inside edge approx 227mm.
Approx. 260mm overall diameter. inside edge approx 227mm.
Rubber strip for laying in the well of your wheel before fitting an inner tube, supplied and marked as 17" size only.
For smaller size applications the tape can be pulled apart at the...
For smaller size applications the tape can be pulled apart at the...
Inner tubes for tyres - offset valve for 16" and 18", straight and offset valves available for 17" size.
5.00 x 16"
6.00 x 16"
4.50 x 17"
5.25/5.50 x 18"
5.00 x 16"
6.00 x 16"
4.50 x 17"
5.25/5.50 x 18"
Inner tubes for tyres - offset valve for 16" and 18", straight and offset valves available for 17" size.
5.00 x 16"
6.00 x 16"
4.50 x 17"
5.25/5.50 x 18"
5.00 x 16"
6.00 x 16"
4.50 x 17"
5.25/5.50 x 18"
Inner tubes for tyres - offset valve for 16" and 18", straight and offset valves available for 17" size.
5.00 x 16"
6.00 x 16"
4.50 x 17"
5.25/5.50 x 18"
Marked 175/185R16 -...
5.00 x 16"
6.00 x 16"
4.50 x 17"
5.25/5.50 x 18"
Marked 175/185R16 -...
Inner tubes for tyres - offset valve for 16" and 18", straight and offset valves available for 17" size.
5.00 x 16"
6.00 x 16"
4.50 x 17"
5.25/5.50 x 18"
straight valve, used...
5.00 x 16"
6.00 x 16"
4.50 x 17"
5.25/5.50 x 18"
straight valve, used...
Inner tubes for tyres - offset valve for 16" and 18", straight and offset valves available for 17" size.
5.00 x 16"
6.00 x 16"
4.50 x 17"
5.25/5.50 x 18"
Off-set valve
5.00 x 16"
6.00 x 16"
4.50 x 17"
5.25/5.50 x 18"
Off-set valve
Inner tubes for tyres - offset valve for 16" and 18", straight and offset valves available for 17" size.
5.00 x 16"
6.00 x 16"
4.50 x 17"
5.25/5.50 x 18"
5.00 x 16"
6.00 x 16"
4.50 x 17"
5.25/5.50 x 18"
When balancing wire wheels it is essential for them to be fitted correctly to the wheel balancing machine. If the wheel is mounted using incorrect contact points (i.e. not mounted on its tapered...
When balancing wire wheels it is essential for them to be fitted correctly to the wheel balancing machine. If the wheel is mounted using incorrect contact points (i.e. not mounted on its tapered...
When balancing wire wheels it is essential for them to be fitted correctly to the wheel balancing machine. If the wheel is mounted using incorrect contact points (i.e. not mounted on its tapered...
We stock a selection of vintage pattern tyres, predominantly for the Ford model range we cover. These are usually Excelsior brand (or alternatively Waymaster) which are made off the old Firestone...
We stock a selection of vintage pattern tyres, predominantly for the Ford model range we cover. These are usually Excelsior brand (or alternatively Waymaster) which are made off the old Firestone...
We stock a selection of vintage pattern tyres, predominantly for the Ford model range we cover. These are usually Excelsior brand (or alternatively Waymaster) which are made off the old Firestone...
We stock a selection of vintage pattern tyres, predominantly for the Ford model range we cover. These are usually Excelsior brand (or alternatively Waymaster) which are made off the old Firestone...
We stock a selection of vintage pattern tyres, predominantly for the Ford model range we cover. These are usually Excelsior brand (or alternatively Waymaster) which are made off the old Firestone...
Decorative chrome rim trim for 13" wheels. This item fits against the inner edge of the outer steel wheel rim, being held in place with the integral clips as shown on main picture.
Export of this...
Export of this...
Decorative polished stainless steel rim trim for 14" wheels. This item fits against the inner edge of the outer steel wheel rim, being held in place with the integral clips as shown on the main...
Decorative plain polished stainless steel rim trim for 15" wheels. This item fits against the inner edge of the outer steel wheel rim, being held in place with the integral clips as shown on the...
Decorative plain polished stainless steel rim trim for 16" wheels. This item fits against the inner edge of the outer steel wheel rim, being held in place with the integral clips as shown on the...
Decorative chrome rim trim for 17" wheels. This item fits against the inner edge of the outer steel wheel rim, being held in place with the integral clips as shown on the main picture.
Export of...
Export of...
Stainless steel domed wheel nut for the Model Y, 7/16"UNF thread, 3/4" A/F hex flats, overall length 1".
Aluminium front hub grease cap, preventing grit getting into the taper roller bearing, fitted between 1932 to 1955.
Threaded base and hexagonal top. 45mm in diameter x 30mm tall, 38mm across the...
Threaded base and hexagonal top. 45mm in diameter x 30mm tall, 38mm across the...
Front wheel bearing retaining washer with inner locating tab.
Dimensions, 32mm o/d x 16mm i/d x 2.5mm thick with a 3mm key way tag.
Dimensions, 32mm o/d x 16mm i/d x 2.5mm thick with a 3mm key way tag.
Prices shown include VAT @ 20% where applicable
