Plastic top hat badge fixing cup, fits into 7/32" panel hole and accepts an 5/32" pin.
Parts
Plastic top hat badge fixing cup, fits into 1/4" panel hole and accepts an 3/16" pin.
10mm (internal) wide folded steel channel will suit most applications, zinc plated finish. This popular formed channel is offered in lengths of 600mm only and suitable for both single and double...
Clip "Ford type" for weatherstrip, fits into side slot. Dimensions approx 16mm long, 13mm high, side clip 4.6mm wide, gripper width max 2.5mm. Per packet of 10 pieces
Oval head chromium plate bumper bolt, 35mm x 22mm appox. 3/8" BSW (approx 10mm) thread, 9.6mm square under head, length approx 32mm. Steel (nut and) bolt, embedded in brass head.
Plated brass clamp for securing Pytchley sliding roofs. Approx 62mm diameter, supplied with leather pressure pad, clamp washer and tightening knob.
Plated brass clamp for securing Pytchley sliding roofs. Approx 62mm diameter, supplied with leather pressure pad, clamp washer and tightening knob.
Plated brass clamp for securing Pytchley sliding roofs. Approx 62mm diameter, supplied with leather pressure pad, clamp washer and tightening knob.
Bonnet/hood catch supplied with pocket. Polished stainless steel parts, 91mm tall overall, base 55mm wide. Choice of 2 hole mount (13mm deep) or 3 hole mount (30mm deep).
Bonnet/hood catch supplied with pocket. Polished stainless steel parts, 91mm tall overall, base 55mm wide. Choice of 2 hole mount (13mm deep) or 3 hole mount (30mm deep).
Bonnet/hood catch supplied with pocket. Polished stainless steel parts, 91mm tall overall, base 55mm wide. Choice of 2 hole mount (13mm deep) or 3 hole mount (30mm deep).
Chrome on brass fitting. Base approx 45mm x 16mm, 28mm deep overall. Mounting holes 31mm centres.
2 x Diecast alloy jaws with springs.
Jaws 34mm long, 11.5mm wide & 13.5mm tall.
Springs 19.5mm long x 9.3mm diameter.
Jaws 34mm long, 11.5mm wide & 13.5mm tall.
Springs 19.5mm long x 9.3mm diameter.
Oval chrome finish and blue enamelled badge with mounting stud 'Ford' fit into bonnet ornament 8215 oval chrome finish and blue enamelled badge with mounting stud "Ford"
4 hole female taper wedge - cast bronze - base approx 61mm x 27mm
2 hole female taper wedge - cast - base approx 55mm x 28mm. Wedge is offset on the base. Please check before ordering.
2 hole female taper wedge - cast in bronze. Base approx 55mm x 28mm. Wedge is offset on the base. Please check fitting match before ordering.
Wire spring slip for securing cowls and bonnet side trim. Wire diameter is 1.1mm, width of the part that slides into the trim is 5.5mm.
Replacement locking device with 2 keys for most outside handles fitted to Y and C through the 'Upright' range of car and van including E83W, overall length including cam peg 46mm, tumbler body...
Stainless steel bonnet catch with T top/bar grip pattern. 95mm long, two screw base (mount holes 35mm centres) mounts horizontally.
spoon end for grill top, chrome, model C and CX fit badge 8213 in the oval
2 hole female taper wedge - cast in bronze - base approx 55mm x 28mm. Wedge is central on the base. Please check before ordering.
blank chassis plate for 100E & 300E. black on aluminium
black on aluminium, rectangular, blank chassis commission plate used January 1965 onward.
Pre-62 black on aluminium, diagonal format, blank chassis commission plate, used until December 1961
black on aluminium, diagonal format, blank chassis commission plate
replacement chassis commission plate for upright models, not stamped, black on aluminium
oval chrome finish and blue enamelled badge with mounting stud "Thames" fit into bonnet ornament 8215
Chrome plated handle 89mm long with oval escutcheon 23mm x 18mm. Short 5/16" (8mm) square shaft. Also fits Ford Dexta Major.
Flat base hook type budget lock. Base 112mm x 25mm. Select right hand or left hand please.
Flat base hook type budget lock. Base 112mm x 25mm. Select right hand or left hand please.
Flat base hook type budget lock. Base 112mm x 25mm. Select right hand or left hand please.
chrome dog leg ornament extension fitting off headlamp bezel on DeLuxe saloon and estate models. we supply in car set (pair) only. E103-NB-1 for right hand and E104-NB-1 for left hand.
Remanufactured chrome front lamp surround bezel. Supplied as car set only (2 pieces) E113-PC-1 right hand, E114-PC-1 left hand
chrome plated reproduction outside locking door handle used on side rear door Thames 400E model.
re-manufactured 7CWT chrome plate name plate for radiator grill panel (under bonnet panel) with Thames word plastic insert fitted. we offer the this with a moulded plastic rear engraved red...
front chrome chevron pints as fitted to Super model front wing/fender for two side strip end finish. offered as a pair only, one piece each E243-PD-1 and E244-PD-1 parts.
chrome plate round badge with black backing for rear quarter panel
Early coloured roundel badge for rear quarter panel with rear chrome mounting. 5 gold star on red with light grey outer written Product of Ford Motor Co Ltd. Used to September 1961
Coloured roundel badge with chrome base for rear quarter panel. 5 gold stars on red background with plain off white outer. Chrome base. Originally used September 1961 onwards.
enamel on chrome Prefect badge - fits into front bonnet trim 1949 to1953
chrome plated 'a Ford product made in England' plaque, per pair (left and right side)
Chrome bumper bar with mounting holes and hole for starting handle.
Please note that base models were fitted from works with painted bumper bar however Prefect always has chrome bumper bar.
This...
Please note that base models were fitted from works with painted bumper bar however Prefect always has chrome bumper bar.
This...
Chrome bumper bar with 6 bracket mounting holes for Prefect - rear
Plain pattern 125mm long, chrome finish, escutcheon hole centres approx 34mm, locking
Plain pattern, non-locking,125mm long, chrome finish, escutcheon hole centres approx 34mm.
Chrome rear bumper bar with 2 bracket mounting holes for Anglia and Popular.
Note that base models were usually fitted with painted bumpers by works.
This product incurs the oversize shipping fee.
Note that base models were usually fitted with painted bumpers by works.
This product incurs the oversize shipping fee.
oval chrome finish and red enamelled badge with mounting stud "Anglia" fit into bonnet ornament 8215
spoon end for grill top, chrome, 125mm long fit badge 8213 in the oval
chrome rear quarter panel upper moulding extension trims - parts E512-AM-1 (right side) and E513-AM-1 (left side) as used on Super model sedan. these are chrome on brass/bronze new castings with...
Prefect 100E horn push button centre badge, three sword black shield on a red background, 50mm (2") in diameter with three locating lugs.
New plastic moulded part, hand painted in our...
New plastic moulded part, hand painted in our...
chrome plated 'Ford' plaque, per pair (left and right side)
pair (two pieces) of front outer bumper iron mounting brackets. note these are used examples, been blasted and primer paint, but will require bend resetting. limited availability.
Fluted pattern 115mm long, chrome finish, escutcheon hole centres approx 34mm, locking.
Fluted pattern 115mm long, chrome finish, escutcheon hole centres approx 34mm.
Ford Prefect rear name badge for models E93A and E493A. Deep chrome finish onto cast metal. Two threaded bosses to rear. Supplied with 2 studs, nuts and washers. Made in the UK
Round dished plate with pull flat spring retaining clip
Chrome moulding for rear body finish, offered in left and right pieces together as a pair. new manufacture
Vintage "Ford" Script Emblem. Chrome plated finish with triple plating process. Stud mount design with clips included.
Dimensions 84mm long x 38mm tall.
Dimensions 84mm long x 38mm tall.
Vintage "Ford" Script Emblem. Chrome plated finish with triple chrome plating process. Double sided tape fixing.
Dimensions 82mm long x 39mm tall.
Dimensions 82mm long x 39mm tall.
We offer replacement keys, cut for door and ignition switch. These are cut to number only, 2 keys are supplied. Supply is restricted to the following key series - key sequence numbers MRN1 through...
we regret we do not cover paints or finishes, nor do we have paint swatch colour shades. please contact either of the following specialist paint suppliers Classic Car Paints Direct or The Car...
grill ornament mount, rechromed. straight top edge.
limited supply -
limited supply -
Deluxe version with polished stainless steel adjustable bracket. Includes ready-to-use black textured fiberboard visor with edge detail. Removable bracket for easy disassembly if you choose to...
Moulding clip/rivet, for fixing body moulding strips to vehicle side. To fit moulding with approx 9mm gap (clip measurements on larger image) supplied with fixing rivet for 3mm hole. Sold each.
Moulding clip/rivet, for fixing body moulding strips to vehicle side. To fit moulding with approx 14mm gap supplied with fixing rivet for 3mm. Sold each.
Chrome plate on brass fitting with 1/4" (approx 6mm) hole. base 45mm x 15mm, mounting holes 31mm apart.
Bonnet catch plate for mounting to bonnet panel. Base approx 72mm tall x 46mm at widest point. Lower hole centres are 31mm.
Accepts the B-16758 rubber buffer. Ford applications originally....
Accepts the B-16758 rubber buffer. Ford applications originally....
front chassis cross-member with starting crank guide, Model Y 1932-37
2 Diecast alloy jaws & 2 Springs.
Jaws 27mm long x 10mm wide x 14mm tall,
Spring 25.5mm long x 6mm diameter tapering to 7.9mm.
Jaws 27mm long x 10mm wide x 14mm tall,
Spring 25.5mm long x 6mm diameter tapering to 7.9mm.
spoon end for grill top, chrome, short rad Y
fit badge 8213 in the oval
fit badge 8213 in the oval
Chrome plate on brass fitting with 1/4" (approx 6mm) hole. Base 45mm x 15mm, mounting holes 31mm apart.
Shaped outside handle approx 100mm long fitted with mounting escutcheon, chromium plate finish. Offered locking or non locking. We offer this handle with a flat base escutcheon (35mm hole centres)...
Shaped outside handle approx 100mm long fitted with mounting escutcheon, chromium plate finish. Offered locking or non locking. We offer this handle with a flat base escutcheon (35mm hole centres)...
Shaped outside handle approx 100mm long fitted with mounting escutcheon, chromium plate finish. Offered locking or non locking. We offer this handle with a flat base escutcheon (35mm hole centres)...
Replacement hinge pin, spring, tag washer and nut for 38mm tall steel self aligning hinge. Order brass ball separately. Dimensions overall length 47mm (43mm under countersink), 6mm diameter...
pair (2 piece) Long Rad model Y wing stay brackets with headlamp mount flange.
blasted and primed only.
may need minor re-bend to get to correct shape curve.
blasted and primed only.
may need minor re-bend to get to correct shape curve.
Chrome on brass fitting. Base 48mm x 19mm, mounting holes 32mm centres.
Stainless steel domed end plug/cap for model Y bumper bar end
spoon end for grill top, chrome, long rad Y fit badge 8213 in the oval
Spoon end for grill top, chrome, long rad Y. *****Same chrome finish on bronze casting but with some surface imperfections in the casting and therefore the chrome finish*****
Fit badge 8213 in...
Fit badge 8213 in...
Prices shown include VAT @ 20% where applicable
