brake rod pedal shaft lever to cross shaft, celvis fork at one end and threaded at the other, overall length 182mm, the shaft has a slight crank manufactured in at the yoke end. 1934-37
Parts
Pedal shaft bracket brass bush, dimensions:- length 19mm, O/D 21mm, I/D 19mm.
front brake cross shaft, fits into pedal bracket assy and operates brake rod levers, used on single rod braking 1934-37 only, 190mm long x 15.8m diameter.
rear brake bell crank lever bush, used with 8" brakes 1939-45. 14.3mm o/d x 12.6mm i/o x 27.5mm long.
Clutch or brake pipe. 100E & 300E used on front brakes, rear brake flexi and clutch slave cylinder,107E used on front brakes and rear brake flexi, 105E rear brake flexi only.
handbrake cable retainer clip, holds handbrake cable into handbrake cross rod bracket.
Brake shoe steady post bush (felt) axle set of 4 pieces . Model E83W will require two pieces instead of one per post. (order double quantity)
Approx dimensions :- 17mm diameter x 10mm thick...
Approx dimensions :- 17mm diameter x 10mm thick...
front brake wheel cylinder connecting brake pipe, flared with convex ends and fitted with two male union nuts.
As Girling part 64217022. Please check individual application. Supersedes part E56-FB-1. Leyland reference 37H6134
Re-lined axle set brake shoes (4 shoes), used front or rear on E83W 10cwt 1938-57. Exchange Item.
axle set brake shoe linings (4 piecves) with rivets, Model E83W 1938-57.
Brake expander roller, dimensions 9.5mm diameter x 7.9mm wide.
good used front brake expander plunger, E83W 10cwt only, overall dimensions 44mm long x 19mm diameter.
brake shoe pull off spring. total overall length 125mm relaxed, 13.7mm diameter, 4 parts required per axle.
good used brake adjuster housing for E83W 10cwt for front and rear brakes
good used brake adjuster wedge, threaded wedge which acts on the adjuster plungers 7/16" square on end.
rear brake dust cover plate for E83W, overall dimensions 98mm long x 36mm wide with 76mm hole centres.
brake pedal frame bracket shaft lever, fits between brake pedal linkage and brake compression unit, E83W 10cwt.
Ford E83W. Special shouldered bolt for front brake cross cable link lever.
Dimensions :- Overall length 71mm, Shoulder drilled and grooved 40mm long x 12.5mm diameter, 3/8" UNF thread 16mm long.
Dimensions :- Overall length 71mm, Shoulder drilled and grooved 40mm long x 12.5mm diameter, 3/8" UNF thread 16mm long.
handbrake relay assy RHD 47-57. refurbished exchange item. incorporates parts E83W-2749, E83W-2752, E83W-2753
threaded clevis yoke (adjustable), brake compression unit to centre brake lever. new fabricated part.
Re-lined axle set brake shoes (4 shoes), used on Model Y 1932-34 with stepped roller. Exchange Item.
brake show return spring short, overall length 94mm, 12.7mm diameter.
used 1932 to 1934.
used 1932 to 1934.
pack of 4 x Y-2036 and 2 x Y-2035 brake shoe springs used 1932-34. (long one at top and two short at bottom). offered as 'axle set' only.
Brake shoe pull off return spring - short, overall length 74mm, 10.9mm diameter. Used 1932 to 1934.
front brake operating wedge stud washer, new/old stock, early Model Y 1934-37
good used front brake drum/hub grease baffle, catches excess grease/oil escaping from front hub oil seal/retainer. 1932-59
front brake operating pin 140mm long, used 1932-34.
approx 140mm long - balls shape to both ends.
approx 140mm long - balls shape to both ends.
Ford Model 19, Y (fits 1932 - 1934) Right side rear brake camshaft
Left side rear brake camshaft for Ford Model 19, Y (fits 1932 - 1934)
rear brake camshaft lever, right hand 32-33, dimensions 80mm long, fits on 13mm shaft, receives 9/32" clevis pin.
rear brake camshaft lever, left hand 32-33, dimensions 80mm long, fits on 13mm shaft, receives 9/32" clevis pin.
Brake or Clutch pedal pad assy, Pyramid rubber bonded onto a reinforced metal plate with a 7/16" UNF stud and nut. Pedal pad 75mm tall x 58mm wide, mounting stud 7/16" dia x 18mm long.
Re-lined axle set brake shoes (4 shoes), used on Model Y 1932-34 with non stepped roller. Exchange Item.
approx 25.5mm diameter. with or without inner shoulder.
approx 25.5mm diameter. with or without inner shoulder.
Brake shoe roller celvis pin as used on CE-2019-B brake shoes 1934-37.
Head approx 11.6mm dia x 4.20mm deep. Shaft 18mm under head to pin hole.
Head approx 11.6mm dia x 4.20mm deep. Shaft 18mm under head to pin hole.
clevis pin - 9/32" diameter x 1 3/8" long (used with double brake lever CE-2235 and CE-2236)
Clevis yoke end, threaded 1/4" UNF, with hole for 9/32" diameter pin. Approx. 52mm long overall.
Wire support bracket for the front brake rod on Model Y & C 1932-37.
metal brake rod support frame complete with rubbers fitted - bolts to the torque tube to support brake rods.
handbrake cross shaft lever L/H LHD 1933-37 rod brakes
handbrake cross shaft lever L/H RHD 1933-37 rod brakes
Prices shown include VAT @ 20% where applicable
