Ford 105E horn push button centre badge, 5 star on a red background in a knurled silver ring, 53mm overaul diameter, with a 43.5mm diameter boss on the back.
New plastic moulded part, hand...
New plastic moulded part, hand...
Parts
Remanufactured part. Chrome on brass sand casting long strip for mounting on to bonnet top up to 1957 on Anglia, Escort and Thames 5cwt. Studs on base pass through holes in bonnet panel. Please...
Remanufactured part. Chrome on brass sand casting long strip for mounting on to bonnet top up to 1957 on Anglia, Escort and Thames 5cwt. Studs on base pass through holes in bonnet panel. Please...
Remanufactured part. Chrome on brass sand casting long strip for mounting on to bonnet top up to 1957 on Anglia, Escort and Thames 5cwt. Studs on base pass through holes in bonnet panel. Please...
Very popular classic interior door handle 109mm long. Cross pin fixing on to 3/8"/10mm square shaft which is parallel (see picture) to line of handle. Chrome plate finish
Chrome plated window winder to fit 3/8"/10mm square shaft. 108mm long. Ford part ref BE-964280-H
Long chrome strip ornament which fits to early model side wing (fender) 1953 to 1957. Offered in PAIRS only comprising 1 piece 100E-16188 and 1 piece 100E-16189. Lost wax cast bronze finished in...
ESCORT chrome plate on brass casting. Nameplate for the front of car.
remanufactured part. chrome on sand cast brass for mounting on to bonnet top up to 1957 on Prefect, Squire and Thames 7cwt. three studs on base pass through holes in bonnet panel.
new remanufacture to original pattern, chrome plated finish. fitted 1957 onward.
Chromed later pattern rounded bumper. front or rear. used 1957 onward on all saloons, also used on early Morgan etc. Please note these are too large to be sent on our standard parcel service and...
Later pattern narrow type over rider with angled bolt location. For the post 1957 bumpers. Also fits Morgan etc. chrome finish.
Chrome plated reproduction handle. For right hand front door of right hand drive model
chrome plated reproduction handle. for left hand front door of right hand drive model, all left hand rear doors.
chrome plated reproduction handle. for right hand front door of left hand drive model, all right hand rear doors.
Prefect 100E grille & boot handle badge, three sword black shield on a red background, 38mm (1-1/2") in diameter.
New plastic moulded badge, hand painted in our workshop.
Please note the red...
New plastic moulded badge, hand painted in our workshop.
Please note the red...
replacement locking device with 2 keys for outside handles fitted 100E range of car and van , overall length including cam peg 35mm, tumbler body diameter 12mm, locking cam diameter 8mm, key...
Plastic ivory coloured moulded escutcheon (comprising base E0TTA-7322630 , spring E0TTA-7322624 and stainless ring E0TTA-7322632) offered as a unit.
left hand drive, inner and outer cable assembly, approx 51" long (approx 1295mm)
chrome plated reproduction handle. for left hand front door of left hand drive model
Ford Popular rear name badge for 103E and 104E. Deep chrome finish onto cast metal. Two threaded bosses to rear. Supplied with 2 studs, nuts and washers. Made in the UK
oval chrome finish badge with mounting stud "Ford Popular"
fit into bonnet ornament 8215
fit into bonnet ornament 8215
oval chrome finish and red enamelled badge with mounting stud "Ford Popular" fit into bonnet ornament 8215
chrome plate name plate with red ANGLIA infill badge for mounting on to radiator grill panel (under bonnet panel). although NOT original part it is a good remake. we offer the this with a moulded...
new made outside door handles - offered as one each left and one right side of vehicle. without locking device - you fit your own old device. sold in pairs only.
new made outside door handles - offered as one each left and one right side of vehicle. with new key locking device fitted. sold in pairs only. see alternative listing without key device
Chrome on brass reproduction front mudguard 'dog leg' ornament. Part 107E-16168 right hand and 107E-16169 left hand. Sold in pairs only (1 left + 1 right). These are brass sand castings, hand...
Blue Ford emblem on silver back (not White). used mid 1961 onward - fixed to nearside front wing. pins 50.5mm apart also used on: Ford Cortina, Escort & Consul
replacement plastic moulded side trim moulding clip/rivet, for fixing body moulding strips to vehicle side. to fit trims with 5.25mm gap (measurements on larger image). this clip is a moulding...
Moulding Clip/Rivet, for fixing body moulding strips to vehicle side, slides into the strip. arrow head push clip requires hole approx 10mm. will suit ford 100E with the 20.65mm side strips, to...
Chrome on brass folded centre bonnet strip. 1270mm (50") long, 21mm wide. Side panels are folded and slide in place. This part will need to be cut shorter by user for some applications. If sent at...
Folded steel side strip for sliding into bonnet strip, one piece 48"/1220mm long. Weld to flat panel. 25mm overall width (flange 14mm) Please note this item exceeds the dimensions for our standard...
Keyhole escutcheon - flap is hinged at the top and opens up against a spring. 2 hole (21mm centres) fixing in base plate - chromium finish. Approx 29mm diameter.
Ford triangle chrome wing badge with " FORD MOTOR COMPANY LTD. ENGLAND " engraved,
Blue Ford oval emblem on silver back. Dimensions 88mm long x 25mm tall, held with two 3mm pins with 50mm centres. Used approx 1966 onward and mounted to lower near side wing.
Moulding clip, for fixing body moulding strips to the vehicle side. To fit mouldings with an approx. 11mm gap (clip measurements on larger image) supplied with fixing rivet for 3mm hole. Will suit...
Moulding clip/rivet, for fixing body moulding strips to the vehicle side. Supplied with fixing rivet for 3mm hole. Will suit ford 100E with the 16mm side strips, 1956 - 61. sold each.
Spring loaded escutcheon for interior door handles and window winders. Chrome finish, approx 38mm diameter x 17mm high. Centre hole approx 15mm.
Plain T boot handle approx 108mm, escutcheon hole centres 36mm, chrome plated. Available locking only.
16mm wide x approx 4.5mm thick. this product is impregnated to produce a dark brown stiff beading (as original product) which will acts as the rubbing tape between bonnet (hood) and radiator cowl...
Leathercloth covered fender welt, stitched over plastic cord centre, bright (shiny) patent look finish, black only. Approx. 6mm diameter bead, 32mm flange
Leathercloth covered fender welt, stitched over plastic cord centre, dull grained finish approx 6mm diameter bead, 32mm flange.
Stocked in the following colours - Green, Grey, Blue, Maroon,...
Stocked in the following colours - Green, Grey, Blue, Maroon,...
Leathercloth covered fender welt, stitched over plastic cord centre, black dull grained finish, approximately 6mm diameter bead, 32mm flange
Leathercloth covered fender welt, stitched over plastic cord centre, bright (shiny) patent look finish, black only. approx 8mm diameter, 32mm flange
Leathercloth covered fender welt, stitched over plastic cord centre, dull grained finish, black only. Approx 8mm diameter, 32mm flange, we can make other sizes of piping to order, minimum 10...
Velvet lined rubber, for 4.5mm glass, overall width 10mm x height 10mm. Flexible channel.
later pattern 1957 onward, rounded bumper, with starting handle hole. used on front of Escort, Squire and 300E models.
re-manufactured 5CWT chrome plate name plate for radiator grill panel (under bonnet panel) with Thames word plastic insert fitted. we offer the this with a moulded plastic rear engraved red...
Shaped wire trim clip, used to secure E83W radiator shell mouldings (18 required per vehicle) as well as other applications. 1/2" dia head with 7/8" long prongs.
British Pre-focus P36D headlamp connector with lead. Double contact with three pin bayonet bulb holder, three wires with headlamp bowl sealing grommet and soldered bullet connecters, overall...
Sealed beam headlamp connector with lead, nylon block three Lucar (6,3mm spade) connector, three wires with headlamp bowl sealing grommet and soldered bullets, overall length 850mm.
Leathercloth covered fender welt, stitched over plastic cord centre, bright (shiny) patent look finish, black only. Approx 4mm diameter, 32mm flange.
Leathercloth covered fender welt, stitched over plastic cord centre, dull grained finish, approx 4mm diameter, 32mm flange, black only.
Interior lever handle 110mm long, chrome plate, fixed with screw through top. 5/16"/8mm square shaft size, can be fitted at various angles of incline.
Locking chrome plated swept type door handle, supplied in PAIRS only to suit left and right of vehicle. Escutcheon hole centres 36mm, Matched key sets.
Chromium plated swept type door handle, supplied singly to suit left and right of vehicle.
Chromium plated swept type door handle, supplied singly to suit left and right of vehicle.
Chromium plated swept type door handle, supplied singly to suit left and right of vehicle.
chrome plated reproduction outside locking door handle used on left or right front driver door Thames 400E model. if two handles are ordered at same time we should be able to supply same key for both.
Used to hold badges to panels, when originals are no longer available. Will fit a mounting post approx 5.5mm, outside diameter 14.5mm. Sold in packets of 10.
Used to hold badges to panels, when originals are no longer available. Will fit a mounting post approx 4.9mm, outside diameter 11.6mm. Sold in packets of 10.
Chromium plated domed head bolt with flats beneath (supplied with washer and nut). Choice of round head 14.5mm head diameter x 26mm long x 5/16" (approx 8mm) thread OR flat head 15.7mm head...
Chromium plated domed head bolt with flats beneath (supplied with washer and nut). Choice of round head 14.5mm head diameter x 26mm long x 5/16" (approx 8mm) thread OR flat head 15.7mm head...
Chromium plated domed head bolt with flats beneath (supplied with washer and nut). Choice of round head 14.5mm head diameter x 26mm long x 5/16" (approx 8mm) thread OR flat head 15.7mm head...
Flexible metal single channel, felt/rubber/moquette lined, overall width approx 14.5mm, height 13mm. For glass thickness 4.7mm to 6.4mm. Black woven edge. Our best selling window channel
Weatherstrip for exterior or interior use. Fitted between the door and the opening window glass. 17mm high, 5mm deep, with galvanised edge bead, one side plush fur pile finish. Sold per 2m length...
'T' boot handle approx 95mm long, escutcheon hole centres 44mm, chrome plated.
'T' boot handle approx 95mm long, escutcheon hole centres 44mm, chrome plated.
'T' boot handle approx 95mm long, escutcheon hole centres 44mm, chrome plated.
'Silent-travel' lock, as used on MG and other pre-war cars, chrome finish 63mm wide 75mm tall body, chrome cover. Facility for shaft of exterior handle to fit into back. Use striker plate part...
'Silent-travel' lock, as used on MG and other pre-war cars, chrome finish 63mm wide 75mm tall body, chrome cover. Facility for shaft of exterior handle to fit into back. Use striker plate part...
'Silent-travel' lock, as used on MG and other pre-war cars, chrome finish 63mm wide 75mm tall body, chrome cover. Facility for shaft of exterior handle to fit into back. Use striker plate part...
Copper bifurcated rivet, 7.5mm head, stem 3.8mm x 11mm. for fixing bonnet tape etc. Per packet 10
Hollow bead, black plastic wing piping. Use between wing (fender) and body (fender welt). Available in the following sizes:
4mm bead x 25mm flange
5.5mm bead x 25mm flange
7mm bead x 25mm...
4mm bead x 25mm flange
5.5mm bead x 25mm flange
7mm bead x 25mm...
Hollow bead, black plastic wing piping. Use between wing (fender) and body (fender welt). Available in the following sizes:
4mm bead x 25mm flange
5.5mm bead x 25mm flange
7mm bead x 25mm...
4mm bead x 25mm flange
5.5mm bead x 25mm flange
7mm bead x 25mm...
Replacement spherical brass hinge pin ball, 5/8" (16mm) diameter
Bumper over-rider bead, black plastic, approx. 10mm wide base with a central 2mm wide slot for fitting on to the metal edge. Triangular section.
Weatherstrip for exterior or interior use, fits between door and drop window glass, narrow version, 11.5mm high, 5.5mm thick. Black pile with stainless steel side bead. Often used on early Ford....
Plastic with solid bead, approx 6mm diameter bead with 25mm flange, stocked in various colours:
BLACK, BLUE, GREEN, GREY, OLD ENGLISH WHITE, RED
BLACK, BLUE, GREEN, GREY, OLD ENGLISH WHITE, RED
Plastic with solid bead, approx 6mm diameter bead with 25mm flange, stocked in various colours:
BLACK, BLUE, GREEN, GREY, OLD ENGLISH WHITE, RED
BLACK, BLUE, GREEN, GREY, OLD ENGLISH WHITE, RED
Plastic with solid bead, approx 6mm diameter bead with 25mm flange, stocked in various colours:
BLACK, BLUE, GREEN, GREY, OLD ENGLISH WHITE, RED
BLACK, BLUE, GREEN, GREY, OLD ENGLISH WHITE, RED
Plastic with solid bead, approx 6mm diameter bead with 25mm flange, stocked in various colours:
BLACK, BLUE, GREEN, GREY, OLD ENGLISH WHITE, RED
BLACK, BLUE, GREEN, GREY, OLD ENGLISH WHITE, RED
Plastic with solid bead, approx 6mm diameter bead with 25mm flange, stocked in various colours:
BLACK, BLUE, GREEN, GREY, OLD ENGLISH WHITE, RED
BLACK, BLUE, GREEN, GREY, OLD ENGLISH WHITE, RED
Plastic with solid bead, approx 6mm diameter bead with 25mm flange, stocked in various colours:
BLACK, BLUE, GREEN, GREY, OLD ENGLISH WHITE, RED
BLACK, BLUE, GREEN, GREY, OLD ENGLISH WHITE, RED
Plastic with solid bead, approx 6mm diameter bead with 25mm flange, stocked in various colours:
BLACK, BLUE, GREEN, GREY, OLD ENGLISH WHITE, RED
BLACK, BLUE, GREEN, GREY, OLD ENGLISH WHITE, RED
Bumper over-rider bead, black PVC, approximately 4.5mm diameter with a central 2mm wide slot for fitting on to the metal edge. Round section.
Rigid single channel felt/rubber/moquette lined, approx 14mm wide x 14mm high, glass 4.7mm to 6.4mm. Sold per 2m length but can be cut to reduce delivery charges, please specify cut lengths...
oval chrome finish and blue enamelled badge with mounting stud "Fordson"
fit into bonnet ornament 8215
fit into bonnet ornament 8215
Chrome on brass folded centre bonnet strip, 845mm length (33.25") 21mm wide. Side panels are folded and slide in place. This part is offered in the longer length for the listed vehicles. The...
Stainless steel ringed bonnet knob, 34mm diameter. With three engraved circles in face.
Chrome on brass fitting. Base 45mm x 16mm, mounting holes 32mm centres.
oval chrome finish and red enamelled badge with mounting stud 'Ford' fit into bonnet ornament 8215
spoon end for grill top, chrome, 105mm long
fit badge 8213 in the oval
fit badge 8213 in the oval
Chrome plate on brass lever handle, 120mm long. Suits 3/8"/10mm square shaft.
Chrome plated spun brass trim ring for handle and winder, 46mm diameter, centre hole approx 16mm.
pre cut from original patern, rubber mud flap, fits to the bottom of the front wing, has pre cut holes and slot for wing brace, fitted to vehicles 1939 onwards. sold in pairs (2 parts = 1 car)...
oversize replacement hinge pin, 0.4mm (1/64") larger than standard pin for use when hinge body is worn. (use of oversize will require holes in hinge to be enlarged from standard).
Replacement hinge pin, standard size, dimensions 65mm overall length x 7.2mm stem diameter (knurling under head 7.5mm approx)
Prices shown include VAT @ 20% where applicable
